Its back 2014 Formula 1 The power unit explained

I love motors and this is some motor 1600cc, V6 turbocharged.

Click here to read about this years F1 Motor

uprs34laef

————————————————————————————————————————————————-

For all your Custom Car & Motorcycle Parts Manufacture and Welding / Repairs
SEE -
www.flashcustoms.co.uk
Don`t forget to email or call us for all your custom made 1 off bespoke items.

Alloy welding / repairs, custom parts, Welding Instruction.

Thanks for reading our blog – we hope this has been of use to you.

Custom made Aluminium, Stainless and Mild Steel Parts for all makes and models.

BMW kit of parts for Throttle Body swap over

Pictured below is a set of parts made up for a BMW Specialist. These guys do some great mods on BMW including power increase modifications and re tuning, spares and accessories.

20140129_091057

We now complete regular batch work for the company for some of the specialist upgrade kits they offer BMW owners.

We can offer 1 off parts or batch parts, or complete assemblies to your drawings or designs.

From a simple weld on tab / bracket to a complete throttle body manifold.

———————————————————————————————————————————————-

For all your Custom Car & Motorcycle Parts Manufacture and Welding / Repairs
SEE -
www.flashcustoms.co.uk
Don`t forget to email or call us for all your custom made 1 off bespoke items.

Alloy welding / repairs, custom parts, Welding Instruction.

Thanks for reading our blog – we hope this has been of use to you.

Suzuki Srad Fuel Tank Pump Flange Modifications

Suzuki Srad Fuel Tank Pump Flange Modifications

A typical fault with the Suzuki SRAD tank was the pump seal arrangement on the bottom of the tank.

If the pump and flange plate were removed for any reason and then refitted, there was a big chance that with a fraction excessive tightening of the clamp bolts that the spot welded flange would distort and then the sandwiched seal ring would not pull tight against the flared opening flange of the tank.

Major problem if you had done the above, filled the tank and had fuel pouring out the bottom of the tank on a nice hot engine / gearbox casing. Very poor design by Suzuki really.

Anyway, my customer having spent a good wedge of cash on getting his tank repainted was left in the same position the first time he put new fuel in his nice newly painted tank. Upon inspection it could be seen that the flange the clamp bolts thread into had distorted and hence the seal ring was not sealing against the tank flange lip.

1394333_10201812688990600_1496320034_n

As can be seen from the image above the original set up takes the form of a 4mm thick flange that is spot welded to the main tank in between the threaded bolt positions, you may also be able to see the dimples in the tank under the positions where the clamping bolts sit through the flange so the bolts dont actually damage the tank shell. You can also see the pressed up flange around the opening that the seal ring actually seals against when the whole thing is tightened up. Clearly also shown are the positions where the spot welds have been positioned in between the drilled and tapped holes.

1451558_10201812688110578_1319495453_nAbove image shows where I have had to drill out the spot welds in the original flange in order to get the damn thing off – best spot welds I have ever removed! This took a bit of tugging and hammering to get off and the next image shows that I then had to do a little panel beating with a small aluminium block to level the panel work back up a bit.

1488167_10201812686750544_1878547800_nA little bit of flushing off and a bit of sanding down and cleaning up and we are ready to fit the new flange.

1477649_10201812687190555_1337374619_n

Laser cut, mild steel, thicker 6mm pump mounting flange offered up in place on the original tank. This will be tacked and welded in  place using a 10mm thick top plate to help soak some heat away and to help stop the new flange from distorting whilst welding.

1st we need to drill and tap out the holes. Drill out 5mm (4.8mm actually) diameter in order to tap M6. I did this using a battery drill set at low torque setting to prevent breaking the tap off in the hole. Notice that I didnt get the holes laser cut as this leaves a “hard” surface on the material which is a nightmare to thread out then, so all I did was get the laser to put a cross mark exactly where the holes come, ensuring dead accurate marking.

1461168_10201812687470562_548027505_nOnce all the holes were drilled and tapped out, a double check on the orientation and bolt the blanking flange up, sett up on the tank for accurate tack up.

1465371_10201812685430511_1213561555_nOnce tacked up, I removed the blanking plate and double checked the tack up and positioning. I had to make sure that I clamped the tank panel work tight up to the flange. Unfortunately even with the new flange tacked tight up I still had a gap to fill where the original dimples in the tank are, so I had to weld as cool as possible but a large fillet size to cover the dimples.

601593_10201812684590490_1838420620_nOnce the weld had had time to cool down I removed the blanking plate, although the flange had stayed flat and level there was a bit of shrinkage in the panel work.

The blanking plate was the used as a template to make a silicon rubber seal for testing, I also had to drill the blank plate and weld 2 pipe stubs on so that I could connect an airline and pressure blow off valve.

The seal and clamping plate were bolted back in place and tightened up I connected an airline one side and a pressure relief blow off valve the other. Spraying soapy water around the welded area and then pressuring up the tank if there is a leak you can see air bubbles bubbling out of pinholes etc.

1422412_10201812680470387_1229572719_n (1)1477370_10201812683110453_1967566878_n (1)

On to dry off, clean up, bit of paint and jobs a good un!

Just waiting for the laser cut nitrile seal to clamp up and finish the job.

———————————————————————————————————————————————–

For all your Custom Car & Motorcycle Parts Manufacture and Welding / Repairs
SEE -
www.flashcustoms.co.uk
Don`t forget to email or call us for all your custom made 1 off bespoke items.

Alloy welding / repairs, custom parts, Welding Instruction.

Thanks for reading our blog – we hope this has been of use to you.
Recommended sites
FLASH CUSTOMS – Specialist Custom Car & Motorcycle Parts
Automotive LED Lights – Car & Motorcycle LED Lighting Solutions
Loaded Wallet – Discount and cash back offers

Email – sales@flashcustoms.co.uk

——————————————————————————————————————————————————————

Want to make savings on your bills?
Want to make savings on your bills?

——————————————————————————————————

Can you write a simple blog ? You too could also be earning an income from blogging!

EN_Paid-To-Blog-Banner

Ducati Oil Catch Tank

Ducati Oil Catch Tank

A nice little fabricated aluminium oil catch tank to fit up behind the head stock and between frame spars on a customers special build Ducati motorcycle.

Initially a simple card mock up was made and changed several times just to get the tank to sit tight up and at the right angle to the frame miss all parts required.

995201_614518405260671_1390513078_n

Once the mock up was complete and we was happy with it, I cut out and pressed up the tank in 2 sections of 1.5mm ns4 aluminium.

Just to make sure I tacked the tank up and we tried it in position to ensure it wasnt going to catch anything as it is maneuvered into place. Once held in position we could see what actual room we had available to us and where we could put breather, site glass, filler cap (to empty in this case), and of course the mounting points. Very little room was left and we decided to mount the tank on welded brackets to each side frame spar, this also then needed thought to be able to bolt the tank in position. The best idea we came up with was to machine top hat, blind threaded bosses to weld into the bottom of the tank. Shown below.

1382397_614518408594004_1194232634_n (1)

Now the mounting top hats are welded in we can see that there is very little room for the breather and inlet pipe, made from 6mm aluminium tube with a 1mm wall thickness.

67062_10201573501611065_1449171905_nSo above you can see that the bottom of the tank is quite “busy”, the pipes had to be welded into the bottom of the tank as there was no room above or down the sides of the tank to run flexible hoses.

1380439_10201573500891047_1419960809_nSo if we look at the other fittings on the tank you can see the black filler bung is on the top, the sight gauge is mounted half way down the tank (black with clear lens) and if the oil mist ever fills enough you will see oil in the tank.

Both of these fittings had a simple little machined threaded boss with a “flange” round the top. My customer actually provided the machined fittings, only the filler threaded fitting had very little top flange to weld to. This with aluminium can be a problem as unless we have a flange with a little “meat” on it will rapidly be saturated in heat and “blow” away before we fuse to the main tank.

Aluminium dissipates heat very quickly unlike stainless steel or mild steel, but as this tank was so small and thin it quickly became “heat saturated” and you really have to watch the heat input otherwise the weld will “flood out” and look poor as well as being uneven and have massive excess penetration into the tank.

249077_614518415260670_1364078305_nAbove you can see how small the flange was on the filler boss, only approx 2mm in section.

67062_10201573501611065_1449171905_nSo once complete and welded up the tank needed to be tested for leaks, a simple process whereby we block all the holes up, add air pressure into the tank and simply brush soapy water around all the joints and welds. If there are any pin holes then the air will bubble through. Luckily this had no such issue.

14138_10201573502131078_872299244_n

Above you can see the finished article and the basic drawing we worked to.

Now the tank is complete my customer is taking the whole bike to Italy to a specialist frame builder to have a frame built.

————————————————————————————————————————————————-

For all your Custom Car & Motorcycle Parts Manufacture and Welding / Repairs
SEE -
www.flashcustoms.co.uk
Don`t forget to email or call us for all your custom made 1 off bespoke items.

Alloy welding / repairs, custom parts, Welding Instruction.

Thanks for reading our blog – we hope this has been of use to you.

Drifting Taster Session at Santa Pod

Get your pulse racing with this exhilarating Drift Racing Taster Experience at Santa Pod Raceway now only £69 instead of £180. Save 62% and get Fast n Furious this summer.

CRACKING DEAL

————————————————————————————————————————————————-

For all your Custom Car & Motorcycle Parts Manufacture and Welding / Repairs
SEE -
www.flashcustoms.co.uk
Don`t forget to email or call us for all your custom made 1 off bespoke items.

Alloy welding / repairs, custom parts, Welding Instruction.

Thanks for reading our blog – we hope this has been of use to you.
Recommended sites
FLASH CUSTOMS – Specialist Custom Car & Motorcycle Parts

Making Simple brackets for motorcycle exhaust mounting

Making a simple stainless steel Bracket / Mounting plate.

20131020_130318 20131020_130447 20131020_130502 20131020_130721 20131020_13104320131020_132531

The selection of images above from left to right show simple steps in making a pair of stainless steel exhaust

mounting brackets. The stainless steel brackets have been hand cut from 3mm thick 304 stainless steel sheet.

I have used a 0.8mm thick cutting disc in a 115mm grinder to slice through the stainless. These are purposely for stainless steel material and slice through it like butter. You do have to be very careful though as any sideways movement will shatter the disc.

A cardboard template had been posted to me, I had simply marked around the template with marker pen, used a centre punch to dot the hole centres and then once happy with the rough cut out I clamped the 2 plates together in the vice jaws (protected with masking tape to prevent marking the metal). Once clamped together I sanded all the way around the metal plates to ensure that an even size and both plates were to marking out.

Once happy with the size and finish of the plates I used 3 different drill bits for drilling through the plates whilst back to back in the vice jaws.  Now an important thing to remember is to always use a good quality drill bit that has been sharpened correctly – do not drill at a really fast speed setting otherwise you will burn the drill bit out.

To make life easier I have used a 3mm, a 5mm and an 8.5mm drill bit. Pilot drill, intermediate drill and a finished size drill bit. If you can remember to drill holes in stainless steel using a similar process you stand a lot better chance of drilling an accurate hole without burning out drill bits and putting heat marks in the stainless.

Once drilled through the correct size of 8.5mm diameter (clearance for an 8mm bolt) I used a small countersink tool (at a slow speed) to debur the holes.

To complete the job I used a coarse Garry Block to clean and put a light grain in the plates.

A quick check against the template proved the mounting plates to be accurate and therefore ready for packaging and dispatch.

————————————————————————————————————————————————-

For all your Custom Car & Motorcycle Parts Manufacture and Welding / Repairs
SEE -
www.flashcustoms.co.uk
Don`t forget to email or call us for all your custom made 1 off bespoke items.

Alloy welding / repairs, custom parts, Welding Instruction.

Thanks for reading our blog – we hope this has been of use to you.
Recommended sites
FLASH CUSTOMS – Specialist Custom Car & Motorcycle Parts

Moto Guzzi Frame, seat, tank modifications

An ongoing job we have at present is the lengthening of a Moto Guzzi Frame for touring 2 up more comfortably.

Our customer has brought the frame, seat & tank to me to chop about.

Initially I had discussed with the customer his requirements and this guy really knew what he was after (a seasoned Guzzi fan), I had descriptions, drawings and pictures. It is actually very refreshing to have a customer that has thought so in depth about his requirements before even bringing the bike to me. I love customers like this. Since our real forte is offering custom modifications to customers cars / bikes / vehicles or parts very often a project starts as something and ends up being either far more work or ends up being something different to what was wanted at the start. However, this is usually because people have good ideas and yet in manufacture / set up / mocking the job up things have to change a little sometimes due to dimensions, parts clashing, not lining up or physically unable to make something as first thought or designed.

Nice to know though that we always take great delight in customers actually going away with something they love. Our enjoyment is very often seeing a customers face when they collect a part and we know they love what we have done. I for one love to be able to work through a project with customers and lovemaking something out of the ordinary. Very often nowadays this is is helped along by parts being modeled or drawn up on a cad system first whilst pulling the “look” or design of something together – people love to see what they are getting for their money upfront if its possible at all.

Any way here are the first pictures of the Moto Guzzi mods, I will update this blog as we go along with pictures and descriptions.

20131006_202027

Seat roughly chopped and extended 3″

20131006_202039

Showing gap between seat and tank to be filled up

20131006_202057

I am not happy with the way the tank sits on the frame at present so I am going to have to have a jiggle about

20131006_202105

Once I am happy with the tank position, I need to check swing of forks to ensure they dont hit the tank on full lock

20131006_202117

The tank actually sits pretty parallel to the frame spars but I think I am going to have to extend the seam around the bottom of the tank to cover the frame more especially around the area shown above, I am also going to have to move the tank back about 10mm to give sufficient clearance on the forks as they swing to full lock.

FOLLOW UP

20131013_183020

SEAT EXTENDED AND TACKED UP PROPERLY 2″

20131013_183007

Seat fitted back onto frame and temporary mountings

20131006_202105

Now I can see what gap I have from the new seat position to the tank – approx 10mm to move the tank back to clear forks on full lock.

20131013_183430

OH DEAR. No going back now!

20131013_185227

Tank end tacked back on roughly 75mm further back (just to give me an idea)

20131013_185427

Tank back on frame with end spaced off and positioned to view the general look

20131013_185356

Looking from above, again just as a rough idea we can see how the tank flows into the seat.

20131013_185452

You can see from the picture above that I have dropped the tacked in position tank end down to try and get the top of the tank to flow into the seat nicely. This totally messes up the side of the tank in that the press lines in the tank sit approx 20mm lower on the end compared with the rest of the tank. Effectively the customer wants the back end of the tank to “flow” nicely along the frame rail so once I get the end in the correct position I will have to fabricate a “dummy” panel to make the tank flow with the bottom seam along the centre line of the frame top rail (if you understand ?). See the next picture to understand the flow of the tank lines.

20131013_185727

From the above picture you can see that the lines in the side of the tank either need chopping and altering or we lift the chopped off end of the tank to get the lines level along the side view and then chop and lift the top of the tank to change the flow of the top of the tank.

All of the below pictures show you the issues we will have now we have extended the tank. The main tank will need slicing up and new material adding in to change the profile of the tank and ensure that the lines of the tank, position of mounting, bottom seam position are all aligned and “aesthetically pleasing to the eye”. This will be where the work starts!

20131013_185713 20131013_185636 20131013_185622

Next step was to start slicing the tank to open out the taper to “flow” towards the front of the seat.

Slicing the tank is not for the faint hearted as once this is undertaken, the plunge has been taken and there is no going back.

20131109_115139

So there you go – above, tank sliced and “tabbed”, you can see that I have cut along the natural form lines in the tank. Opening these out has the effect of smoothing the flow of material back to the re positioned end panel.

20131109_145141

Due to the nature of the tank I have decided that we also need to almost “scollop” in 2 new sections along the length of the tank sides to get the material to shape and look right as it meets up to the bottom flange (shown at the top, tank is upside down).

20131109_145148

You can see on this view that I have tacked in a brace plate to ensure that the tank “top” & “bottom” stay at the correct dimension, whilst manipulating the panels to fit.

20131109_145205

As you can see above I have added small tabs to keep the sliced sections apart evenly, as now I have to start removing the longitudinal tacked plates off  a couple at a time to begin the infill process.

20131109_151657

Above, 1st infill panel shaped and tacked in place.

20131109_163307

Once the top infill panel had been tacked in I can now work opposite and start fitting some infill material to the underside.

20131109_163316

Whilst tacking infill panels into the extended tank it is critical to keep checking the dimensions of the gap to ensure that the shrinkage of the tacks does not shrink the panels in too much and create distortion or twist.

20131109_165336

A good “fit up” is essential to keep the tank even and aid the welding process.

20131109_165355

A better view of the underside infills

20131110_171933

Now you can see that the side infill panels will meet up with the top infill panel roughly on the centre of the sliced press lines in the tank. The idea being that the new infill for the longitudinal will have a pressed line in it meeting up with the joint position of the new top and side infill metal. You cant see in the picture below but I have put a slight radius on the ends of the top and side infill plates along the joint so that I dont end up with a sharp pointed joint line as this needs to be a smoother radius to match up with the re fitted end panel and new press line in the longitudinal infill panel.

20131110_171948

And both side infills

20131110_172001

20131110_172001 20131115_195910 20131117_093750 20131116_102910 20131116_094604 20131116_094553 20131115_195921 20131117_102325 20131117_102335 20131117_104137 20131117_140153 20131117_140640 20131117_140704

20131117_140537 20131117_140518 20131117_140437 20131117_140415 20131117_140406 20131117_140324 20131117_140253 20131117_140122 20131117_140134 20131117_140143 20131117_140238 20131117_140153 20131117_140111 20131117_140116

FOLLOW UP – WELDING

20131124_105454

Above – All joints taped up ready for purging the tank with argon to stop atmospheric attack on the back of the welds on the inside of the tank. Each seam was completed one at a time and tape removed as I moved around the joints to spread the heat to ensure I never allowed a build up of heat in one area, which will cause shrinkage and distortion.

20131124_142922

Below, just to show that I have tried to complete all welded joints along an existing press line in the tank, therefore reducing chance of the welded joints shrinking and “sinking” if I chopped and joined the tank on a flat panel / slightly shaped there would be more chance of distortion / sinking where contraction has taken place along joint as it has cooled.

20131124_142933

Common rule in engineering “majority of metals expand upon heating but, nearly always contract more upon cooling”. Using this rule of thumb a skilled engineer will be able to level a flat bar of solid metal e.g. a flange, by strategic pin point heating using an oxy-fuel gas torch.

20131124_142944

Some of the welding does not look good as quite a lot has been welded using the “pull” mig welding method, or “stitch” welding method, and in some instances what we term “backstep” method. All of these methods are used in completing differing joints due to gap, thickness of metal, joint set up and various other anomalies.

20131124_143000

Above a view on the underside of the tank

20131124_143010

You can see above where I have seam welded the small lip where the edges join around the end

20131124_143511

Cut out and patch in of new filler neck and cap assembly.

20131207_135333

Mark up for chop out

20131207_135632

Cut out and mark up for shaping and fitting into existing tank

20131207_140342

Shaped panel with new drain pipe added before we graft in new filler cap

20131207_150047

Tank cut out and panel shaped (bit of panel beating here to reshape panel), offered up for fitting

20131207_150153

Better fit

20131207_150204

Grafted in / welded and flushed in

20131207_154806

From another view

20131207_154814

Back end where welded flange has been previously repaired – not pretty

We need to do something with this and to fill the gap between the tank and frame spar.

20131214_201611

Infil panel and scallop around head stock

20131214_201632

From riders view

20131214_201644

Front flange extensions to cover frame drops tacked on to existing tank.

Note these blend into new mounting bracket panels.

20131220_201234

Scalloped out infil panel for lower rear of tank to blend in with chassis better

20131220_210647

Welded / blended and reshaped front flange extension

20131220_210707

Tacked on infil panel (looks better when side panels on)

20131221_104035

20131221_104042

20131221_104101

20131221_104118

20131221_133621

20131221_105802

Pressure tested and ready to fit properly. Now the whole set up wants to be fitted with all panels and motor / carbs / re-trimmed seat and new mounting rubbers to sit properly on the bike frame and then the work begins, skimming and paint prep.

Hopefully another happy customer ?

CUSTOMER FEEDBACK -

I was not fully sure this job was feasible until I visited Flash Customs for a consultation.
With a full discussion of what was wanted, I was assured it was and it was clearly described to me how it could be done.
I was pleased that I was kept informed every step of the way. The finished article is testimony to the bespoke services that Flash Customs can offer.I would not hesitate to recommend their services. Thank you.

Richard Cresswell

————————————————————————————————————————————————-

For all your Custom Car & Motorcycle Parts Manufacture and Welding / Repairs
SEE -
www.flashcustoms.co.uk
Don`t forget to email or call us for all your custom made 1 off bespoke items.

Alloy welding / repairs, custom parts, Welding Instruction.

Thanks for reading our blog – we hope this has been of use to you.
Recommended sites
FLASH CUSTOMS – Specialist Custom Car & Motorcycle Parts

Ducati Wheel Speed Sensor Bracket

I have recently been asked to manufacture 1 off replacement Ducati wheel speed sensor bracket.

The original one was manufactured as 2 separate pieces and then welded together. This had been knocked and bent.

I managed to straighten this out, nick through the existing weld and re-weld around 3 sides to”repair” the original.

Knowing that this original design may have a weakness where the joint between the 2 parts are only able to be welded on 3 sides, I machined the item as a single part, using a manual lathe and mill.

The material I used was HE30 Aluminium, or  what is now commonly known as “6082 grade alloy” or “T6″.

Particulars of this grade of material is ideal for this application – “Alloy 6082 is a medium strength alloy with excellent corrosion resistance. Alloy 6082 has the highest strength of the 6000 series alloy. Due to the higher strength of Alloy 6082 it has replaced Alloy 6061 in many applications. Alloy 6082 is typically used in highly stressed applications, Trusses, Bridges, Cranes, Transport applications, Ore Skips, Beer Barrels, Milk churns”. (taken from http://www.aircraftmaterials.com/data/aluminium/6082.html 30/9/2013).

A more typical application for this grade is aircraft parts, billet alloy slab yokes, fork clamps, handlebar risers.

20130919_20480920130919_204822

Above image shows 1 piece sensor bracket, machined from billet T6 Alloy, etch primed and painted silver

————————————————————————————————————————————————-

For all your Custom Car & Motorcycle Parts Manufacture and Welding / Repairs
SEE -
www.flashcustoms.co.uk
Don`t forget to email or call us for all your custom made 1 off bespoke items.

Alloy welding / repairs, custom parts, Welding Instruction.

Thanks for reading our blog – we hope this has been of use to you.
Recommended sites
FLASH CUSTOMS – Specialist Custom Car & Motorcycle Parts

Motorcycle Polished Stainless Steel Battery Box

Several things need to be considered when designing a Custom Motorcycle building a battery box.

  1. Size – to allow battery to fit
  2. Shape – for battery fit and also where on the bike it will fit
  3. Mounting method / position e.g. brackets, flanges, bolt fixing, welded to frame, removable.
  4. Will it sit snug in its space and be fixed strongly enough – as a battery can weigh a good bit.
  5. Will it interfere / hit / affect operation of / with other components e.g. gearbox, carbs / throttle bodies, side panels, seat, rear panel, electrics etc.
  6. Can you access the battery terminals easily should you need to?
  7. Consider mounting and positioning so that terminals do not touch or foul and arc onto another metal part of the motorcycle.
  8. Drain, in case battery leaks.
  9. Battery is held in position / fixed by clamps, rubber straps etc.
  10. Do fuses need to be located or relays on the battery box or near to it – is there room for them and fixings to hold them in place?
All these things may be a simple point to note but if you are building a battery box in what ever material you do not want to find that after you have spent good time and money it will not fit and be secured in the designated area.
When we deal with customer requests for battery boxes or trays for cars or motorcycles we very often ask – “have you made a cardboard mock up of what you want to check that it will fit ok”?
Inevitably if not there can be issues of the manufactured box or tray not fitting correctly, hitting or fouling on other components, difficulty locating it, rubbing or damaging frameworks (especially after you have paid a lot of money for a paint job) during fitting etc etc. For a small amount of time messing about with scissors, cardboard & sellotape you can save yourself both time, money and grief.

Battery Tray Customer Drawing

Anyway we recently received this drawing from the customer and had a couple of emails and phone calls to clarify things and make sure he got what he wanted and we could manufacture as a 1 off item at the most economical cost.

One or two bits were redesigned and we ended up with an easier slightly cheaper item to manufacture which was good for all involved.

Once all happy we proceeded to manufacture parts to make up the battery box from stainless steel, this was going to be mirror polished and so during marking out (using scribe, rule, square), cutting out (using guillotine &  cutting disc) we needed to be very careful not to mark the surface.

We used Stainless Steel 304 grade, PC1 – Plastic Coated 1 side, 1.5mm thick, the idea is the plastic coating provides resistance to marking etc during manufacture, we have also in the past covered the whole surface in masking tape to prevent marking. Once all the parts had been marked out, cut out and folded where required it was time to tack weld and assemble all the parts -

Parts ready for Assembly, edges pre polished

Before tacking the parts together we made sure that the edges were pre polished – this makes it far easier when final polishing the parts after assembly and welding.

Tack Welded Panels

As you can see in the above 2 images, “tack up” and “set up” is critical in getting any job right 1st time, It is worth spending a few minutes more at these stages as if not it will take a lot longer to sort out the consequences at a later stage.

For example if the job is tacked up out of square and then welded up you would have to cut out all the welds to be able to get the job squared up properly, time consuming, messy and it will never be the same. If you tack up a joint out of level for example you can get a larger gap one end compared to the other and this may affect the size of the weld where you have welded along and then found you have to lay a larger fillet to “fill” the gap, this can also increase risk of distortion and penetration through the joint, both of which may cause problems later.

So the idea when cutting and forming this job was to make sure that we got our panels sized correctly so that we could achieve a neat corner corner joint at the tack up stage between panels. see B below !

 

If the joint was not quite set to a corner joint we simply closed down the tack using a small Pin Hammer, this is sufficient for closing the gap down as minimal effort and “weight” is need to do this.

When all parts are tacked together and the joints are all neat closed down corner joints this will be ideal for a neat bead of weld along them, after checking the job for square again.

Fuse Welded Joint

 As we achieved a good set up of the joints we were able to “fuse weld” them together, this is a method where as no filler wire is added to the molten pool of weld, the edges of the material are simply melted together as we run along the joint. If you are an experienced welder you can set up your machine to achieve this easily as long as you get your rate of travel along the joint correct. If not then you will get a build up of localised heat and excess penetration and in some cases a nice hole in the joint just where you dont want it.

I completed the welding of this job by using the TIG welding process which for this kind of  job is ideal as it is a very “neat” and “precise” method of welding when compared to MIG welding .

Polished Battery Box

Using the TIG welding “fusion” welding method I was able to mirror polish the complete job without sanding or blending in the welds as these were “smooth and flush” to the material and looked neat and tidy as they were “laid”.

Unfortunately for me my motor on my polisher died a death whilst trying to finish polishing this job and I had to polish by sander and hand – this took me 3 times as long and still ended up not quite 100% up to my standards. As several sides of the battery box will not be seen when in situ it should be fine though once fitted.

4.5 inch grinder with polishing attachments

For all your Custom Car & Motorcycle Parts Manufacture and Welding / Repairs

SEE -

www.flashcustoms.co.uk

Don`t forget to email or call us for all your custom made 1 off bespoke items.

Thanks for reading our blog – we hope this has been of use to you.

Recommended sites

FLASH CUSTOMS – Specialist Custom Car & Motorcycle Parts
Loaded Wallet – Discount and cash back offers
Cash Back – Cash Back & Money Saving offers